Analysis of the influence of turning parameters of CUZN39PB3 and AW 6060 materials on surface roughness
Vol 116 No 2 (2022), Articles
Vol 116 No 2 (2022)

Analysis of the influence of turning parameters of CUZN39PB3 and AW 6060 materials on surface roughness

Articles
https://doi.org/10.7862/tiam.2022.2.2
Published June 30, 2022
Leszek Tomczewski
Rzeszów University of Technology, Faculty of Mechanical Engineering and Aeronautics, Al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland
https://orcid.org/0000-0002-1743-5495
Jagoda Muszyńska-Pałys
Rzeszów University of Technology, Faculty of Mechanical Engineering and Aeronautics, Al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland
https://orcid.org/0000-0002-1743-5495
PDF

Keywords

turning, non-ferrous metals, surface roughness

How to Cite

Tomczewski, L., & Muszyńska-Pałys, J. (2022). Analysis of the influence of turning parameters of CUZN39PB3 and AW 6060 materials on surface roughness. Technologia I Automatyzacja Montażu (Assembly Techniques and Technologies), 116(2), 8-14. https://doi.org/10.7862/tiam.2022.2.2
ACM ACS APA ABNT Chicago Harvard IEEE MLA Turabian Vancouver

Download Citation

Endnote/Zotero/Mendeley (RIS) BibTeX

Abstract

The article presents an analysis of the turning parameters of two non-ferrous materials. The tested materials were: brass CuZn39Pb3 and aluminum alloy AW 6060. A Kyocera turning knife and a WNMG 080404 AH plate were used to make the samples. Three parameters were tested: rotational speed, feed and depth of cut at three levels of variability. The roughness parameters Ra and Rz were selected for the analysis. On the basis of the obtained results, it was shown that the feed used during machining has the greatest influence on roughness, while the change of depth or cutting speed does not cause significant differences in roughness.

This is an Open Access article distributed under the terms of the Creative Commons Attribution License CC BY 4.0 (https://creativecommons.org/licenses/by/4.0/)

https://doi.org/10.7862/tiam.2022.2.2
PDF

References

Adamczak S. 2008. „Pomiary geometryczne powierzchni. Zarysy kształtu, falistość i chropowatość”. Warszawa, WNT.

Bordeasu I., Mitelea I., Salcianu L., Craciunescu C.M. 2016. “Cavitation Erosion Mechanisms of Solution Treated X5CrNi18-10 Stainless Steels”. Journal of Tribology-Transactions of the ASME 138(3).

Eskelinen H., Eskelinenn P. 2003. “Micorwave Component Mechanics” Artech House.

Galanis, N.I., Manolakos, D.E. 2010. ”Surface roughness prediction in turning of femoral head”. Int. J. Adv. Manuf. Technol., 51(1-4), pp. 79-86.

Grzesik W. 2015. „Wpływ topografii powierzchni na właściwości eksploatacyjne części maszyn”. Mechanik, nr. 8-9, pp. 587-593.

Lazar I. et al. 2021. “The behavior to cavitation erosioncorrosion of the CuZn39Pb3 brass structures, obtained by in-depth heat treatments”. Journal of Physics: Conference Series 1781.

Leach R. (ed.). 2013. “Characterization of areal surface texture”. Berlin. Springer.

Pawlus P. 2005. “Topografia powierzchni. Pomiar, analiza oddziaływanie”. Rzeszów. Oficyna Wydawnicza Politechniki Rzeszowskiej.

Tomczak J., Pater Z. 2010. „Próby doświadczalne procesu walcowania poprzeczno-klinowego odkuwek ze stopów aluminium w gatunkach AW i 2618A”. Obróbka Plastyczna Metali t. XXI nr 4 pp.249-260

http://m.abplanalptools.pl/m-katalog-narzedzi/m-kyoceranarzedzia-skladane.html (28th April 2022).

https://www.sandvik.coromant.com/en-us/knowledge/materials/pages/workpiece-materials.aspx (28th April 2022).

https://www.taylor-hobson.pl/urzadzenia-warsztatowe/surtronic-s128/ (28th April 2022).